Saturday, August 5, 2023

IEC 62304 Software Unit Implementation and Integration

Hi friends!!!


In our previous blogs, we have discussed about the following topics.


IEC 62304 Software Architectural & Detailed Design


IEC 62304 Software Requirements Analysis


IEC 62304 Software Development Planning


IEC  62304 Overview & Definitions


IEC 60601-1 Definitions


IEC 60601-1 Classification of Medical Electrical Equipment


IEC 60601-1 General Requirements for Testing Medical Electrical Equipment


IEC 60601-1 Medical Electrical Systems


IEC 60601-1 Protection against unwanted and excessive radiation hazards


IEC 60601-1 General Requirements


IEC 60601-1 Programmable Electrical Medical Systems 


IEC 60601-1 Hazardous situations and fault condition


IEC 60601-1 Construction of Medical Electrical Equipment


IEC 60601-1 Leakage Currents and Patient Auxiliary Currents


IEC 60601-1 Creepage Distance and Air Clearance


IEC 60601-1 Components and Wiring


IEC 60601-1 Mechanical Hazards Moving Parts


IEC 60601-1 Excessive Temperatures


IEC 60601-1 Markings on the Outside of Medical Electrical Equipment


IEC 60601-1 Markings on the Inside of Medical Electrical Equipment


IEC 60601-1 Instability Hazards


IEC 60601-1 Separation of Parts


EU MDR Assessment Routes


EU MDR Timeline, Annex, Chapter


EU MDR Post Market Surveillance


EU MDR Clinical Evaluation


EU MDR Technical Documentation - Part 1


EU MDR Technical Documentation - Part 2


EU MDR General Safety and Performance Requirement


EU MDR Information on the Label


EU MDR Post Market Clinical Follow Up


EU MDR Unique Device Identification - Part 1 


EU MDR Unique Device Identification - Part 2


EU MDR Classification Rules


EU MDR EUDAMED


EU MDR Economic Operators


EU MDR Chapter & Articles - Part 1


EU MDR Chapter & Articles - Part 2


In today's blog, we are going to discuss about IEC 62304.


IEC 62304 states the requirements for Medical Device Software. Satisfying the requirements of IEC 62304 is an important task in order to ensure the safety of patients and efficacy of software used in treating the patients.


Therefore, it is important for Medical Device QA/RA Professionals to understand about Software Unit Implementation, Integration & Integration Testing requirements as per Clause 5.5 & 5.6 of IEC 62304. 


Software Unit

As per IEC 62304, the Software Items which cannot be further decomposed are called as Software Units.


Software Unit Implementation:

The Manufacturer of the medical device software shall implement each software units. This requirement is applicable for Class A, B, C, medical device software.


The procedures, strategies and methods shall be established by the manufacturer of medical device software for verifying the software units. If the verification of software unit is done by testing, the adequacy of the test method shall be evaluated by the manufacturer. This requirement is applicable for Class B & C, medical device software.


Prior to integrating the software units with larger software items, the manufacturer of the medical device software shall establish the acceptance criteria for each software units and shall ensure that the software unit meets the acceptance criteria. This requirement is applicable for Class B & C medical device software.

The following factors can be considered for acceptance criteria:

The software code implements adequate risk control measures, free from contraindications with respect to the interface design, comply to applicable programming or coding standards.


The software unit verification shall be performed by the manufacturer of medical device software and results shall be documented. The software unit verification means verifying the software unit implementation against the software unit design. This requirement is applicable for Class B & C medical device software.

Software Unit Integration and Integration

Testing:

The manufacturer of medical device software shall integrate each software units. The integration of software units with software items and/or software system shall be verified by the manufacturer according to the software integration plan and evidence of such verification shall be retained. This requirement is applicable for Class B & C, medical device software.


The integrated software items shall be tested by the manufacturer of medical device software according to the software integration plan and the results shall be documented. Such integration testing procedures shall be evaluated for adequacy. This requirement is applicable for Class B & C, medical device software.


The intended performance of the integrated software items shall be addressed by the manufacturer of medical device software during the software integration testing. This requirement is applicable for Class B & C, medical device software.

The following factors can be considered during software integration testing:

The functionality of the software.

Appropriate implementation of risk control measures.

Specified timing and other behaviour of the software.

Specified functioning of internal and external interfaces of the software.

The software can be tested under abnormal conditions including foreseeable misuse.


The manufacturer of medical device software shall conduct the regression testing when software items are integrated, to ensure that no defect have been introduced into previously integrated software. This requirement is applicable for Class B & C, medical device software.


The software problem resolution process shall be used by the manufacturer of medical device software to enter details about the anomalies found during integration and integration testing. This requirement is applicable for Class B & C, medical device software.


The integration test records shall document the test results, identify the tester, have adequate details like equipment’s used for testing, environmental conditions, test case specifications etc., to enable the test to be repeated.


Now I hope you have acquired some basic knowledge about Software Unit Implementation, Integration & Integration Testing as per Clause 5.5 & 5.6 of IEC 62304. We will meet again with another valuable topic related to Biomedical Engineering, Medical Device, Healthcare.


NOTE: Dear friends!!!... Please do comment a topic related to Biomedical, so that we can discuss it in future blogs.


Check out for this blog about Computed Tomography,  X ray, MRI scan, ECG.


Generations of CT Scanners


COMPUTED TOMOGRAPHY|TECHNOLOGY|ARTIFACTS


x ray machine working principle


components of x ray tube


MRI scan 


MRI With Contrast


Brain MRI


Types of MRI scanners


ELECTROCARDIOGRAM


12 Lead ECG Placement


HOW TO READ AN ECG


Holter Monitor


DON’T FORGET TO FOLLOW THIS BLOG PAGE


DROP YOUR MAIL ID TO GET IMMEDIATE UPDATES


If you find this blog post knowledgeable, 

comment & share it with a friend! 

 

 

No comments:

Post a Comment